Between the bottom of a breastplate and the top of a greave there is a lot of body to protect: the belly, the hips, the groin and the long muscles of the thigh. In a suit of plate armor, this zone was handled by a family of pieces with names that sound confusing today: the fauld, the culet, the tassets and the cuisses. Museum catalogs use these words, and once you know them, every armor in a museum or a reenactment photo becomes easier to read.
For a LARP player, hip and thigh armor is the part that turns a chest piece and a helmet into a complete armored figure. It also changes how you move: you have to sit, run, kneel and climb stairs in these pieces. In this guide, we explain what each piece is, how its overlapping plates were joined, what surviving examples in museums tell us, and how to choose hip and thigh armor for your character and your event.
Hip and Thigh Armor at a Glance
The table below uses the vocabulary of museum catalogs. Terms were not always used in the same way in every period or country, so treat it as a practical map rather than a rulebook.
| Piece | What it protects | How it is built | Attached to | LARP characters |
|---|---|---|---|---|
| Fauld | Waist and front of the abdomen | A few overlapping curved lames | Lower edge of the breastplate | Knights, officers, commanders |
| Culet | Lower back | A few lames at the lower edge of the backplate | Lower edge of the backplate | Full plate knights, champions |
| Tassets | Upper front and sides of the thigh | One plate, or several lames joined flexibly | Hanging from the fauld or breastplate | Soldiers, knights, mercenaries, battle priests |
| Cuisses | The thigh | Steel plates, often with a knee cop | Worn on the thigh, usually with a knee defense | Heavy knights, paladins, veterans |
| Poleyns | The knee | A cup over the kneecap, with articulated lames and a side wing | Worn at the knee | Any armored character |
Why the Hips and Thighs Needed Their Own Armor
Armor did not appear all at once. According to the Metropolitan Museum of Art, mounted warriors commonly wore mail leg coverings called chausses by 1200. Later, as crossbows became strong enough to pierce shields and mail, knights first added a coat covered with small plates, and then the armorers developed articulated plate for the legs, arms and hands. The museum dates the arrival of full head to toe plate to about 1420, and a second Met essay says that the development of full plate armor was complete by about 1420.
The same Met essay mentions another early solution for the lower body: the brigandine, a coat in which smaller plates covered the abdomen, hips and back. Hip and thigh plates came out of the same problem: a solid breastplate protects the chest well, but the body below it has to bend, twist and sit. The answer was a series of horizontal lames, thin curved plates that slide over each other like the scales of a fish.
This is the key idea behind everything in this guide. A solid plate gives protection but no movement. Overlapping lames give both, and the way they are joined (with rivets, straps or pins) decides how the piece moves.
If you want to see how mail and plate fit together across the whole period, read The Evolution of Knight Armor: From Mail to Plate.
Fauld: Armor for the Waist and Lower Belly
What a Fauld Is
The fauld is the skirt of plates below the breastplate. The Fitzwilliam Museum defines faulds as pieces of armor protecting the front of the abdomen below the breastplate, made originally of mail and later of plates. Lames, the relatively pliable metal plates used in armor, are what give a plate fauld its flexibility.
Museum records show how this looks on real armor. A breastplate with a fauld and tassets in the Worcester Art Museum, dated 1530 to 1550, has a rounded fauld on a deep waistplate of three lames, and the breastplate overlaps the waistplate and is riveted to it. The record lists a weight of 9 lb 10 oz (about 4.37 kg) for the whole piece.
How the Lames Move
The Metropolitan Museum of Art has a German breastplate from Augsburg, made about 1530, that shows the system clearly. Its record says that the waist plate has a single skirt lame with two turning pins that attach the fauld, which has three lames, and the upper tassets, which have five. Turning pins are small pivots: they hold two plates together but let them rotate against each other. Each tasset in turn carries more lames below it, so the whole hip and thigh defense is a chain of plates hanging from one waist plate.
A Worcester Art Museum record for a fauld with tassets shows a simpler version. Here the fauld is made of two lames that articulate on rivets. The museum notes that this piece is dated to the late 1800s and has been restored, so it is a good illustration of the principle but not a primary witness of medieval practice.
The Culet at the Back
A fauld has a partner at the back, the culet, which is made of lames at the lower edge of the backplate. A museum example is the composed Italian armor in the Metropolitan Museum of Art (object 29.150.7), assembled in its present form in the 1920s from pieces of the Chalcis hoard, whose record lists two culet lames from the backplate.
The culet matters in play for a practical reason: it sits low on the back, near the part of the body you sit on, so a rigid, deep culet can make sitting on a camp chair or a log difficult. Plan your hip armor for the moments between fights too.
Fauld in LARP
In LARP: a fauld gives your torso armor a finished lower edge and a proper silhouette, and it is the natural anchor for tassets. It suits knights, commanders and any character in full or three quarter plate. If you play a lot of roleplay scenes with sitting and talking, choose a shorter fauld with fewer lames, or hip pieces that can be unfastened quickly.
Tassets: Plates for the Upper Thigh
Single Plates and Lamed Tassets
Tassets hang in front of the upper thigh, one on each side. The Fitzwilliam Museum in Cambridge defines them as pieces of body armor that protect the upper thigh and hang at the front on each side of the fauld or breastplate. Each tasset is either one plate or several lames joined flexibly with straps and rivets.
The Royal Armouries puts it even more simply, describing tassets as the armour worn to protect the thighs. Its example is the left tasset of a three quarter field armour that belonged to Henry Wriothesley, 3rd Earl of Southampton, dated about 1595 to 1600, and decorated over its whole surface with etching and gilding.
Upper and Lower Tassets
Some armors had tassets in two stages. On the Augsburg breastplate of about 1530 in the Metropolitan Museum of Art, the lowest lame of each upper tasset has two turning pins that attach the lower tassets, which have seven lames. That means each side of the body has a stack of five lames on top of a stack of seven, and each stack can swing independently. The museum lists the weight of the whole object, breastplate with tassets, at 11 lb 6 oz (5160 g, about 5.16 kg).
The Worcester Art Museum breastplate described earlier has a single, longer tasset on each side, with eight lames, including a deep, curved terminal lame, riveted in place. Both examples show the same approach: lames stacked on top of each other to build a long tasset that can still move.
Tassets for the Tourney
Not every tasset was symmetrical. An Italian armor made about 1575 to 1580, now in the Metropolitan Museum of Art, has asymmetrical upper-thigh defenses made for the tourney, a mock combat between two mounted groups using blunted lances and swords. In the same way, the field and tournament armor made about 1565 for Johann Wilhelm, Duke of Saxe-Weimar, lists tassets (upper thigh defenses) among its pieces for field use.
These records, both titled as armor for field and tournament, are a useful reminder that some armors were assembled as kits, with different pieces for different uses. For a LARP player, the lesson is simple: your hip and thigh pieces can change with the event.
Tassets in LARP
In LARP: tassets are the most practical hip and thigh piece for a player. They protect the part of the leg that is most exposed in a fight, they look impressive from a distance, and because they hang from the waist they usually allow you to walk, run and kneel better than a full cuisse. They are also easy to add to an existing set: a breastplate plus a pair of tassets already reads as a soldier or knight. Read about the tassets we make in the shop section below.
Cuisses: Armor for the Thigh Itself
What Cuisses Are
The cuisse is the thigh defense. The Metropolitan Museum of Art holds cuisses from the Chalcis hoard, which was found in 1840 in the ruins of a Venetian fortress on the island of Euboea, then called Negroponte. The fortress was captured and destroyed in 1470. One pair of steel cuisses from about 1450 weighs 808 g (1 lb 12.5 oz) for one and 720.1 g (1 lb 9.4 oz) for the other.
A second pair in the same museum, dated about 1425 to 1450 and later, is a pair of cuisses with knee defenses (poleyns), made of steel and leather. The right piece weighs 1890.9 g (4 lb 2.7 oz) and the left 1638.6 g (3 lb 9.8 oz). Because these are surviving pieces, and the later ones are noted as restored or composed, they give a rough idea of what a real leg defense weighed.
Cuisses and Poleyns Together
The knee needed its own piece. The Fitzwilliam Museum defines the poleyn as knee armor first seen in the 14th century, with a cup-shaped main piece that fits over the kneecap, often with articulated lames above and below it, and a side wing. Many surviving cuisses are listed together with poleyns, such as the pairs in the Met records for the armors made in Milan about 1570 and about 1575, where each leg piece is described as a cuisse with a knee defense.
A late 16th century Italian armor in the Metropolitan Museum, dated about 1575, gives the following weights for one set of lower body pieces: right tasset 826 g and left tasset 1040 g, right cuisse 1012 g and left cuisse 1126 g. The whole armor weighs about 21.5 kg (47 lb 5 oz).
Cuisses in LARP
In LARP: full cuisses are the most demanding hip and thigh piece. They add coverage and look very convincing on a heavy knight or paladin, but they must be fitted well: if they bind at the groin or knee, you will feel it after an hour. We do not list cuisses as a standard product, but we can make them as a custom piece to order. Our LARP Greaves collection is a good place to start if you want your lower body to match.
How the Pieces Were Fastened and Worn
Armor is not only plates; it is also the system that holds the plates to the body. Several methods are recorded in museum catalogs:
- Rivets. The Worcester breastplate with fauld and tassets has tassets riveted in place, while the breastplate itself is riveted to the waistplate.
- Turning pins. On the Augsburg breastplate of about 1530, turning pins join the skirt lame, fauld and tassets. They hold the plates together while allowing them to pivot.
- Leathers and sliding rivets. The Worcester fauld with tassets was originally hung on leathers, and now uses sliding rivets, apparently a later change.
- Arming points. The Met explains that arming points are pairs of strings normally attached to the arming doublet that secured armor elements to the body. Another Met essay adds that plate was worn over a specially fitted, padded arming doublet, and that points let individual pieces be tied on where needed.
The same Met essay notes that armor was put on starting with the legs, then the upper body and arms, with the helmet and gauntlets last. That is a useful rule for LARP too: dress your lower body first, because it is much harder to bend over to a strap once you have a breastplate on.
The Met also records a fashion that is easy to copy: in the last decade of the 15th century, it became popular in western Europe to wear a short skirt, often of richly adorned fabric, over the armor, and this continued well into the first half of the 16th century. A cloth skirt over the fauld is a cheap way to give a plate set a Renaissance look, and it hides the join between fauld and tassets.
Museum Examples and Their Weights
Weights are always the most discussed detail of medieval armor. The Metropolitan Museum of Art writes that most plate armor is not as heavy as is commonly believed. The table below collects weights published in museum records for the hip and thigh pieces discussed in this guide. They show that single pieces were in the range of roughly half a kilogram to just under two kilograms, and that the whole armor weighed many times more.
| Object | Date | Piece | Listed weight |
|---|---|---|---|
| Pair of cuisses, Italian (Met) | c. 1450 | Thigh defenses | 808 g (1 lb 12.5 oz) and 720.1 g (1 lb 9.4 oz) |
| Cuisses with poleyns, Italian (Met) | c. 1425 to 1450 and later | Thigh and knee defenses | 1890.9 g (4 lb 2.7 oz) and 1638.6 g (3 lb 9.8 oz) |
| Armor, Italian, probably Milan (Met) | c. 1570 and later | Tassets | 544 g (1 lb 3.2 oz) and 523 g (1 lb 2.45 oz) |
| Armor, Italian, probably Milan (Met) | c. 1570 and later | Cuisses with knee defenses | 1078 g (2 lb 6.1 oz) and 939 g (2 lb 1.2 oz) |
| Armor, Italian, probably Milan (Met) | c. 1575 | Tassets | 826 g (1 lb 13.15 oz) and 1040 g (2 lb 4.65 oz) |
| Armor, Italian, probably Milan (Met) | c. 1575 | Cuisses with knee defenses | 1012 g (2 lb 3.7 oz) and 1126 g (2 lb 7.7 oz) |
| Breastplate with tassets, Augsburg (Met) | c. 1530 | Whole object | 5160 g (11 lb 6 oz) |
| Whole armor, Italian, probably Milan (Met) | c. 1570 and later | Whole armor | 16.56 kg (36 lb 8 oz) |
| Whole armor, Italian, probably Milan (Met) | c. 1575 | Full armor | 21.5 kg (47 lb 5 oz) |
The ca. 1570 tasset and cuisse figures come from this Met record. In the two Milan records, the tassets and cuisses of one set together come to roughly 3 to 4 kg, while the whole armor weighs 16.56 kg and 21.5 kg. Also keep in mind that several of the listed armors are composed or restored, so they are best read as examples of weight, not as proof of a single original owner's set.
Fighting on Foot: When Leg Armor Was Left Out
Hip and thigh armor was never universal. The most surprising example in the Metropolitan Museum of Art is the foot-combat armor of Prince-Elector Christian I of Saxony, made in 1591 by Anton Peffenhauser of Augsburg. It weighs 46 lb 3 oz (20.96 kg), and the helmet alone weighs 11 lb 9 oz (5245 g). The museum explains that contestants fought on foot across a waist-high barrier, and that strict rules banned strikes below the belt, so the barrier and rules made leg armor unnecessary.
This tells us something useful about design: armor matched the rules of the fight. When the fight was mounted, the thighs needed tassets and cuisses. When the rules forbade low strikes, they did not. In the same way, a modern LARP event has its own rules about where you can be hit, and those rules, more than history, should decide how much leg armor you need.
In LARP: if your event forbids hits below the belt, or if the fighting is light, tassets alone may be enough. If you are in a big battle with hits on the legs, cuisses and greaves add coverage and a complete look. Read How Does LARP Combat Work? for the basics.
Comparing Hip and Thigh Armor for LARP
Here is how the pieces compare for play. The ratings are our practical judgment from the way the pieces are built, not a lab measurement, and your own body shape will change them.
| Piece | Walking and running | Sitting | Coverage | Fitting effort | Best for |
|---|---|---|---|---|---|
| Short fauld only | Excellent | Good | Low | Low | Light fighters, camp wear |
| Fauld and short tassets | Very good | Good | Medium | Low | All-round play |
| Long lamed tassets | Good | Medium | Medium to high | Medium | Knights, battle characters |
| Upper and lower tassets | Good | Medium | High | Medium | Heavy knights, commanders |
| Cuisses with poleyns | Medium | Medium | Very high | High | Full plate looks, battles |
A simple rule: the more you walk, kneel and sit during an event, the shorter and more flexible your hip armor should be. Many players own two configurations: a lighter one for camp and long days, and a full one for the big battle.
Steel or Polyurethane: Which Hip and Thigh Armor for LARP?
Real hip and thigh pieces were made of steel, and good steel reproductions exist. The museum weights in the table above show what that means for a modern player. A single tasset or cuisse from a historical armor can weigh from roughly half a kilogram to almost two kilograms, and you wear two of each, plus the fauld, plus everything else. Steel also gets hot in the sun, needs oil and care against rust, and can be difficult to fit to a body that is not exactly like the original owner's.
Our armor is cast from polyurethane resin reinforced with fiberglass and painted by hand. It gives you the look of sculpted metal plate, and it can be recolored in your colors for free. Rules still differ from game to game, so always check the armor rules of your event before you buy, especially for pieces that cover the legs. For a deeper comparison of materials, read What Is the Best Type of LARP Armor? and, if you want to know how our pieces are made, our guide to how polyurethane LARP armor is made. Care tips are on our armor maintenance page.
Which Hip and Thigh Armor Fits Your Character
- Northman, tribal warrior: a plain fauld or a short tasset over leather and cloth. See our Northmen and Barbarian collection.
- Knight on campaign: fauld with long lamed tassets, optional cuisses. See our Knight collection.
- Paladin, crusader, templar: heavy tassets and, for a late medieval look, cuisses with poleyns. See our Paladin collection.
- Soldier, mercenary, landsknecht: tassets with a short fauld, easy to wear all day. See our Landsknecht collection.
- Battle priest, witch hunter: practical tassets that allow kneeling and running. See our Battle Priest and Witch Hunter collections.
- Commander or champion: two-stage tassets, a full fauld and matching leg armor. See our LARP Armor Sets.
Our Tassets and Hip Armor
All our armor is made in our workshop in Ukraine from original designs. Hip armor sits in its own collection, LARP Tassets, and many of our armor series include matching tassets. Current tasset designs include:
- Lion Knight Tassets, part of the Lion Knight series.
- Flower Knight Tassets, part of the Flower Knight series.
- Empire Armor Tassets and Empire Commander Tassets, from the Empire series.
- Boneflare Tassets, Crownleaf Tassets, Blackthorn Tassets and Ironvine Tassets.
To match your lower body, add matching greaves from the LARP Greaves collection. Production takes 7 to 21 business days, we ship worldwide, and instalment payments are available.
Want Hip or Thigh Armor That Is Not in Our Shop?
If you dream of a fauld with a particular lame count, two-stage tassets, or cuisses with poleyns in your faction's colors, we can make it. We usually start with a 2D concept, then a 3D sculpt, and then make the mold and the piece. Tell us your idea on our Custom LARP Armor page. If you equip a whole group, orders from 5 players get 15% off: see Group Orders. If you are planning your season, our LARP calendar lists upcoming events.
Further Reading
- The Metropolitan Museum of Art: Breastplate with Tassets, Augsburg, about 1530
- The Metropolitan Museum of Art: Pair of Thigh Defenses (Cuisses) with Knee Defenses (Poleyns)
- The Metropolitan Museum of Art: Foot-Combat Armor of Prince-Elector Christian I of Saxony
- The Metropolitan Museum of Art: The Function of Armor in Medieval and Renaissance Europe
- Worcester Art Museum (Higgins Collection): Breastplate with Fauld and Tassets
- Royal Armouries: Left Tasset of a Three Quarter Field Armour
- The Fitzwilliam Museum: Tassets (terminology)
Want to see how all armor pieces fit together? Read The Evolution of Knight Armor: From Mail to Plate and Types of Medieval Helmets.



